湖北國能優泰電力有限公司
分享到：
10kV 600A T2T型接頭
600A T2T Bol deadbreak connector
-
T2T-15/600
產品應用：
10kV 600A T2T型接頭采用高品質的絕緣橡膠制成,為全絕緣、全密封螺栓連接式終端電纜接頭。產品為600A T型電纜接頭和負荷轉換頭的組合。廣泛應用于戶外美式箱變，開關柜，美式電纜分接箱，地埋式變壓器及其它電氣設備的連接。安裝在600A母排接口上及美式箱變的600A套管上。負荷轉換頭實現600A轉為200A回路與200A肘型電纜接頭或肘型避雷器連接。測試點可安裝帶電顯示器或故障指示器，以便查詢設備帶電狀態和故障狀態。
10kV 600A T2T bol deadbreak connector adopt high quality insulation rubber,fully-insulated,fully sealed.It is the combination for 600A T type cable connector and loadbreak bushing extender. widely used in outdoor american pad-mound transformer, switch cabinet,american cable branch box, buried transformer and other electrical equipment connection.installed in 600A busbar and 600A bushing of american pad-mound transformer. loadbreak bushing extender can achieve 600A turn into 200A loop,and connected with 200A elbow cable connector or elbow arrester. test point can installed charged display or fault indicator, so that to check equipment charged status and fault status。
包裝標準：
T型接頭本體、負荷轉換頭
壓接端子、應力錐
內六角扳手
雙頭螺栓、安裝工具
銅接地線、硅脂、清潔紙
安裝標尺卡、產品合格證
安裝指導說明書
T-body, conversion head
Crimp terminal, cable adaptor
Inner hexagon spanner
Two-head screw,install tools
Copper grounding wire, silicon grease, cleaning paper
Install scale card, product information
Instruction manual
10kV 600A T2T型接頭采用高品質的絕緣橡膠制成,為全絕緣、全密封螺栓連接式終端電纜接頭。產品為600A T型電纜接頭和負荷轉換頭的組合。廣泛應用于戶外美式箱變，開關柜，美式電纜分接箱，地埋式變壓器及其它電氣設備的連接。安裝在600A母排接口上及美式箱變的600A套管上。負荷轉換頭實現600A轉為200A回路與200A肘型電纜接頭或肘型避雷器連接。測試點可安裝帶電顯示器或故障指示器，以便查詢設備帶電狀態和故障狀態。
10kV 600A T2T bol deadbreak connector adopt high quality insulation rubber,fully-insulated,fully sealed.It is the combination for 600A T type cable connector and loadbreak bushing extender. widely used in outdoor american pad-mound transformer, switch cabinet,american cable branch box, buried transformer and other electrical equipment connection.installed in 600A busbar and 600A bushing of american pad-mound transformer. loadbreak bushing extender can achieve 600A turn into 200A loop,and connected with 200A elbow cable connector or elbow arrester. test point can installed charged display or fault indicator, so that to check equipment charged status and fault status。
包裝標準：
T型接頭本體、負荷轉換頭
壓接端子、應力錐
內六角扳手
雙頭螺栓、安裝工具
銅接地線、硅脂、清潔紙
安裝標尺卡、產品合格證
安裝指導說明書
T-body, conversion head
Crimp terminal, cable adaptor
Inner hexagon spanner
Two-head screw,install tools
Copper grounding wire, silicon grease, cleaning paper
Install scale card, product information
Instruction manual